What is steel wire used for in construction?

Metal rope

Steel wire rope (right hand lang lay)

Wire rope is composed of as few as two solid, metal wires twisted into a helix that forms a composite rope, in a pattern known as laid rope. Larger diameter wire rope consists of multiple strands of such laid rope in a pattern known as cable laid. Manufactured using an industrial machine known as a strander, the wires are fed through a series of barrels and spun into their final composite orientation.

In stricter senses, the term wire rope refers to a diameter larger than 9.5 mm (3⁄8 in), with smaller gauges designated cable or cords.[1] Initially wrought iron wires were used, but today steel is the main material used for wire ropes.

Historically, wire rope evolved from wrought iron chains, which had a record of mechanical failure. While flaws in chain links or solid steel bars can lead to catastrophic failure, flaws in the wires making up a steel cable are less critical as the other wires easily take up the load. While friction between the individual wires and strands causes wear over the life of the rope, it also helps to compensate for minor failures in the short run.

Wire ropes were developed starting with mining hoist applications in the 1830s. Wire ropes are used dynamically for lifting and hoisting in cranes and elevators, and for transmission of mechanical power. Wire rope is also used to transmit force in mechanisms, such as a Bowden cable or the control surfaces of an airplane connected to levers and pedals in the cockpit. Only aircraft cables have WSC (wire strand core). Also, aircraft cables are available in smaller diameters than wire rope. For example, aircraft cables are available in 1.2 mm (3⁄64 in) diameter while most wire ropes begin at a 6.4 mm (1⁄4 in) diameter.[2] Static wire ropes are used to support structures such as suspension bridges or as guy wires to support towers. An aerial tramway relies on wire rope to support and move cargo overhead.

History

[

edit

]

Modern wire rope was invented by the German mining engineer Wilhelm Albert in the years between 1831 and 1834 for use in mining in the Harz Mountains in Clausthal, Lower Saxony, Germany.[3][4][5] It was quickly accepted because it proved superior strength from ropes made of hemp or of metal chains, such as had been used before.[6]

Wilhelm Albert's first ropes consisted of three strands consisting of four wires each. In 1840, Scotsman Robert Stirling Newall improved the process further.[7] In America wire rope was manufactured by John A. Roebling, starting in 1841[8] and forming the basis for his success in suspension bridge building. Roebling introduced a number of innovations in the design, materials and manufacture of wire rope. Ever with an ear to technology developments in mining and railroading, Josiah White and Erskine Hazard, principal owners[9] of the Lehigh Coal & Navigation Company (LC&N Co.) — as they had with the first blast furnaces in the Lehigh Valley — built a Wire Rope factory in Jim Thorpe, Pennsylvania,[8] in 1848, which provided lift cables for the Ashley Planes project, then the back track planes of the Summit Hill & Mauch Chunk Railroad, improving its attractiveness as a premier tourism destination, and vastly improving the throughput of the coal capacity since return of cars dropped from nearly four hours to less than 20 minutes.

The following decades featured a burgeoning increase in deep shaft mining in both Europe and North America as surface mineral deposits were exhausted and miners had to chase layers along inclined layers. The era was early in railroad development and steam engines lacked sufficient tractive effort to climb steep slopes, so inclined plane railways were common. This pushed development of cable hoists rapidly in the United States as surface deposits in the Anthracite Coal Region north and south dove deeper every year, and even the rich deposits in the Panther Creek Valley required LC&N Co. to drive their first shafts into lower slopes beginning Lansford and its Schuylkill County twin-town Coaldale.

The German engineering firm of Adolf Bleichert & Co. was founded in 1874 and began to build bicable aerial tramways for mining in the Ruhr Valley. With important patents, and dozens of working systems in Europe, Bleichert dominated the global industry, later licensing its designs and manufacturing techniques to Trenton Iron Works, New Jersey, USA which built systems across America. Adolf Bleichert & Co. went on to build hundreds of aerial tramways around the world: from Alaska to Argentina, Australia and Spitsbergen. The Bleichert company also built hundreds of aerial tramways for both the Imperial German Army and the Wehrmacht.

In the latter part of the 19th century, wire rope systems were used as a means of transmitting mechanical power[11] including for the new cable cars. Wire rope systems cost one-tenth as much and had lower friction losses than line shafts. Because of these advantages, wire rope systems were used to transmit power for a distance of a few miles or kilometers.[12]

Construction

[

edit

]

Inside view of a wind turbine tower, showing the wire ropes used as tendons

Wires

[

edit

]

Steel wires for wire ropes are normally made of non-alloy carbon steel with a carbon content of 0.4 to 0.95%. The very high strength of the rope wires enables wire ropes to support large tensile forces and to run over sheaves with relatively small diameters.

Strands

[

edit

]

In the so-called cross lay strands, the wires of the different layers cross each other. In the mostly used parallel lay strands, the lay length of all the wire layers is equal and the wires of any two superimposed layers are parallel, resulting in linear contact. The wire of the outer layer is supported by two wires of the inner layer. These wires are neighbors along the whole length of the strand. Parallel lay strands are made in one operation. The endurance of wire ropes with this kind of strand is always much greater than of those (seldom used) with cross lay strands. Parallel lay strands with two wire layers have the construction Filler, Seale or Warrington.

Spiral ropes

[

edit

]

In principle, spiral ropes are round strands as they have an assembly of layers of wires laid helically over a centre with at least one layer of wires being laid in the opposite direction to that of the outer layer. Spiral ropes can be dimensioned in such a way that they are non-rotating which means that under tension the rope torque is nearly zero. The open spiral rope consists only of round wires. The half-locked coil rope and the full-locked coil rope always have a centre made of round wires. The locked coil ropes have one or more outer layers of profile wires. They have the advantage that their construction prevents the penetration of dirt and water to a greater extent and it also protects them from loss of lubricant. In addition, they have one further very important advantage as the ends of a broken outer wire cannot leave the rope if it has the proper dimensions.

Stranded ropes

[

edit

]

Left-hand ordinary lay (LHOL) wire rope (close-up). Right-hand lay strands are laid into a left-hand lay rope. Right-hand lang lay (RHLL) wire rope (close-up). Right-hand lay strands are laid into a right-hand lay rope.

Stranded ropes are an assembly of several strands laid helically in one or more layers around a core. This core can be one of three types. The first is a fiber core, made up of synthetic material or natural fibers like sisal. Synthetic fibers are stronger and more uniform but cannot absorb much lubricant. Natural fibers can absorb up to 15% of their weight in lubricant and so protect the inner wires much better from corrosion than synthetic fibers do. Fiber cores are the most flexible and elastic, but have the downside of getting crushed easily. The second type, wire strand core, is made up of one additional strand of wire, and is typically used for suspension. The third type is independent wire rope core (IWRC), which is the most durable in all types of environments.[13] Most types of stranded ropes only have one strand layer over the core (fibre core or steel core). The lay direction of the strands in the rope can be right (symbol Z) or left (symbol S) and the lay direction of the wires can be right (symbol z) or left (symbol s). This kind of rope is called ordinary lay rope if the lay direction of the wires in the outer strands is in the opposite direction to the lay of the outer strands themselves. If both the wires in the outer strands and the outer strands themselves have the same lay direction, the rope is called a lang lay rope (from Dutch langslag contrary to kruisslag,[14] formerly Albert's lay or langs lay). Regular lay means the individual wires were wrapped around the centers in one direction and the strands were wrapped around the core in the opposite direction.[2]

Multi-strand ropes are all more or less resistant to rotation and have at least two layers of strands laid helically around a centre. The direction of the outer strands is opposite to that of the underlying strand layers. Ropes with three strand layers can be nearly non-rotating. Ropes with two strand layers are mostly only low-rotating.[15]

Classification according to usage

[

edit

]

Depending on where they are used, wire ropes have to fulfill different requirements. The main uses are:

• Running ropes (stranded ropes) are bent over sheaves and drums. They are therefore stressed mainly by bending and secondly by tension.
• Stationary ropes, stay ropes (spiral ropes, mostly full-locked) have to carry tensile forces and are therefore mainly loaded by static and fluctuating tensile stresses. Ropes used for suspension are often called cables. [16]
• Track ropes (full locked ropes) have to act as rails for the rollers of cabins or other loads in aerial ropeways and cable cranes. In contrast to running ropes, track ropes do not take on the curvature of the rollers. Under the roller force, a so-called free bending radius of the rope occurs. This radius increases (and the bending stresses decrease) with the tensile force and decreases with the roller force.
• Wire rope slings (stranded ropes) are used to harness various kinds of goods. These slings are stressed by the tensile forces but first of all by bending stresses when bent over the more or less sharp edges of the goods.

Rope drive

[

edit

]

Technical regulations apply to the design of rope drives for cranes, elevators, rope ways and mining installations. Factors that are considered in design include:[17]

• Number of working cycles allowed before replacement or breakage of the rope
• Donandt force (yielding tensile force for a given bending diameter ratio

  D

  /

  d

  ) - strict limit. The nominal rope tensile force

  S

  must be smaller than the Donandt force

  SD1

  .
• Rope safety factor, ratio between the rope's breaking strength and the maximum load to be expected
• Allowable number of broken strands before replacement
• Optimal rope diameter for a given sheave diameter, so as to obtain best working life

The calculation of the rope drive limits depends on:

• Data of the used wire rope
• Rope tensile force

  S

• Diameter

  D

  of sheave or drum
• Simple bendings per working cycle

  wsim

• Reverse bendings per working cycle

  wrev

• Combined fluctuating tension and bending per working cycle

  wcom

• Relative fluctuating tensile force

  ΔS/S

• Rope bending length

  l

Safety

[

edit

]

The wire ropes are stressed by fluctuating forces, by wear, by corrosion and in seldom cases by extreme forces. The rope life is finite and the safety is only ensured by inspection for the detection of wire breaks on a reference rope length, of cross-section loss, as well as other failures so that the wire rope can be replaced before a dangerous situation occurs. Installations should be designed to facilitate the inspection of the wire ropes.

Lifting installations for passenger transportation require that a combination of several methods should be used to prevent a car from plunging downwards. Elevators must have redundant bearing ropes and a safety gear. Ropeways and mine hoistings must be permanently supervised by a responsible manager and the rope must be inspected by a magnetic method capable of detecting inner wire breaks.

Terminations

[

edit

]

Right-hand ordinary lay (RHOL) wire rope terminated in a loop with a thimble and ferrule

The end of a wire rope tends to fray readily, and cannot be easily connected to plant and equipment. There are different ways of securing the ends of wire ropes to prevent fraying. The common and useful type of end fitting for a wire rope is to turn the end back to form a loop. The loose end is then fixed back on the wire rope. Termination efficiencies vary from about 70% for a Flemish eye alone; to nearly 90% for a Flemish eye and splice; to 100% for potted ends and swagings.[citation needed]

Thimbles

[

edit

]

When the wire rope is terminated with a loop, there is a risk that it will bend too tightly, especially when the loop is connected to a device that concentrates the load on a relatively small area. A thimble can be installed inside the loop to preserve the natural shape of the loop, and protect the cable from pinching and abrading on the inside of the loop. The use of thimbles in loops is industry best practice. The thimble prevents the load from coming into direct contact with the wires.

Wire rope clips

[

edit

]

Clamps securing wire rope on logging equipment

A wire rope clip, sometimes called a clamp, is used to fix the loose end of the loop back to the wire rope. It usually consists of a U-bolt, a forged saddle, and two nuts. The two layers of wire rope are placed in the U-bolt. The saddle is then fitted to the bolt over the ropes (the saddle includes two holes to fit to the U-bolt). The nuts secure the arrangement in place. Two or more clips are usually used to terminate a wire rope depending on the diameter. As many as eight may be needed for a 2 in (50.8 mm) diameter rope.

The mnemonic "never saddle a dead horse" means that when installing clips, the saddle portion of the assembly is placed on the load-bearing or "live" side, not on the non-load-bearing or "dead" side of the cable. This is to protect the live or stress-bearing end of the rope against crushing and abuse. The flat bearing seat and extended prongs of the body are designed to protect the rope and are always placed against the live end.[18]

The US Navy and most regulatory bodies do not recommend the use of such clips as permanent terminations unless periodically checked and re-tightened.

Eye splice or Flemish eye

[

edit

]

The ends of individual strands of this eye splice used aboard a cargo ship are served with natural fiber cord after splicing to help protect seamens' hands when handling.

An eye splice may be used to terminate the loose end of a wire rope when forming a loop. The strands of the end of a wire rope are unwound a certain distance, then bent around so that the end of the unwrapped length forms an eye. The unwrapped strands are then plaited back into the wire rope, forming the loop, or an eye, called an eye splice.

A Flemish eye, or Dutch Splice, involves unwrapping three strands (the strands need to be next to each other, not alternates) of the wire and keeping them off to one side. The remaining strands are bent around, until the end of the wire meets the "V" where the unwrapping finished, to form the eye. The strands kept to one side are now re-wrapped by wrapping from the end of the wire back to the "V" of the eye. These strands are effectively rewrapped along the wire in the opposite direction to their original lay. When this type of rope splice is used specifically on wire rope, it is called a "Molly Hogan", and, by some, a "Dutch" eye instead of a "Flemish" eye.[19]

Swaged terminations

[

edit

]

A wire rope sleeve before and after swaging, or crimping

Swaging is a method of wire rope termination that refers to the installation technique. The purpose of swaging wire rope fittings is to connect two wire rope ends together, or to otherwise terminate one end of wire rope to something else. A mechanical or hydraulic swager is used to compress and deform the fitting, creating a permanent connection. Threaded studs, ferrules, sockets, and sleeves are examples of different swaged terminations.[20][21] Swaging ropes with fibre cores is not recommended.

Wedge sockets

[

edit

]

A wedge socket termination is useful when the fitting needs to be replaced frequently. For example, if the end of a wire rope is in a high-wear region, the rope may be periodically trimmed, requiring the termination hardware to be removed and reapplied. An example of this is on the ends of the drag ropes on a dragline. The end loop of the wire rope enters a tapered opening in the socket, wrapped around a separate component called the wedge. The arrangement is knocked in place, and load gradually eased onto the rope. As the load increases on the wire rope, the wedge become more secure, gripping the rope tighter.

Potted ends or poured sockets

[

edit

]

Poured sockets are used to make a high strength, permanent termination; they are created by inserting the wire rope into the narrow end of a conical cavity which is oriented in-line with the intended direction of strain. The individual wires are splayed out inside the cone or 'capel', and the cone is then filled with molten lead–antimony–tin (Pb80Sb15Sn5) solder or 'white metal capping',[22] zinc[citation needed], or now more commonly, an unsaturated polyester resin compound.[23][24]

See also

[

edit

]

References

[

edit

]

Steel wire is a versatile product and is used in many industries. Right from the entertainment as rigging for stunt scenes, to amusement parks for various rides to cranes used in industries such as oil and gas, shipping, and so on, steel wire ropes are present everywhere. Learn how these steel wires are made , their types and applications.

 

Steel is known to be an important raw material for various industries. We have already explained various steel products such as steel plates, TMT bars, aluminium coils, and so on. Just like aluminium coils, steel wire is a versatile product and has varied applications. This article will explain, what steel wire is, how steel wire is made, its benefits and applications.

What is a steel wire?

What is a steel wire? Steel wire is a flexible, cylindrical strand made of steel. It is used for various applications however one of the important uses include lifting heavy materials in construction, logistics, infrastructure industries. Its manufacturing process generally involves several processes such as rolling, surface heating, etc.

How is steel wire made?

Step 1: Generally, the raw material for making steel wires include steel rods which are supplied by integrated or mini steel plants. Steel rods are often made from billets using a hot rolling process.

Step 2: Surface treatment is the next step. Descaling and surfacing coating is done, which further enables the drawing process.

Step 3: The third step of making steel wire is drawing. The rod is brought to the drawing machine and the required diameter wire is drawn.

Step 4: Then, the drawn wire undergoes the patenting process. Patenting is a type of heat treatment wherein the wire is heated at about 900°C and then quenched into molten lead at 500°C.

Step 5: Intermediate drawing takes place.

Step 6: The last step is stranding and closing. Wire and strands positioning is confirmed and closed.

Note: The process of making steel wires may vary depending on a manufacturer

Various companies produce steel wires. Global Wires Business (GWB), a division of Tata Steel, is one of the largest steel wire manufacturers in the world.

Benefits of steel wires/ropes

Steel wire ropes are one of the important components for many industries. Here are some of the benefits of steel wires.

• Corrosion resistance: Steel wires can withstand harsh weather conditions, hence corrosion is less likelihood with steel wires. Sometimes, steel corrosion can take place under certain conditions however, it can be avoided with timely maintenance.
• Tensile strength: Steel wire showcase excellent tensile strength, which makes them an ideal choice for use in the infrastructure.
• Ductility: Many metals deform under tensile strength however, steel wires do not. This is one of the advantages of steel wires. This makes steel wires an ideal choice for use in electrical cables, etc.

Types of steel wires

Depending on the raw material used, the manufacturing process and its usage, there are many types of steel wire available in the market. Some of the popular types of steel wires are listed below:

Stainless steel wire: Stainless steel properties makes it a robust material that does not corrode quickly. Hence, stainless steel wire ropes are ideal for the use where it may come in contact with water and humidity. It is best suited for industries such as marine, architecture, etc.

Galvanised steel wire ropes:  Galvaised wire ropes are coated with molten zinc. As a result, galvanised steel wire ropes display the features such as high strength, corrosion resistance, etc. Therefore, these wire ropes are ideal for general engineering purposes.

Carbon steel wire ropes: There are low and high carbon content steel wire ropes. While carbon adds strength to it compromises flexibility. Hence, low carbon steel wire ropes are used where more flexibility is required. On the other hand, high carbon steel wire ropes are used where the focus is more on strength and not on flexibility.

Coated steel wire ropes: Coated wire ropes are generally coated or jacketed with materials such as polypropylene, PVC, nylon, etc. Such coating offers protection to the steel wire against wear and tear and also corrosion.

Apart from the four types mentioned above, there are various other types of steel wire ropes. Steel wire ropes come in different sizes, such as 3mm, 6mm, 9mm and so on. Additionally, custom made steel wires are made of different types of steel and coating also differs as per the application.

Applications of steel wires/ropes

Steel wire ropes are used for various purposes. Right from the creative music industry to hard-core oil and gas industry, steel wire ropes are present everywhere.

Mining: Mining wire ropes need to withstand harsh environments especially, in the case of underground mining. Therefore, these wires need to be of high quality and strong. As a result, they are made of high-carbon steel.

Logistics: Steel wires are widely used in the logistics industry. They are one of the critical components of cranes that carry bulk and heavy materials. These cranes are mainly deployed in port areas where environment conditions are humid. Therefore, it requires corrosion resistant material. Hence, galvanised steel wires ropes are usually used in the logistics industry.

Construction: In the construction industry various equipment are used to carry heavy materials such as cement blocks, and other raw material and machinery. Also, they are used in securing rebars, lifting elevators carrying materials and so on. Depending on the uses, multiple types of steel wires are used in the construction industry.

Manufacturing: In any manufacturing plant, materials need to be carried from one station to another. For which, various material handling equipment are used. These require steel ropes to carry materials that are heavy and big in size. Depending on the purpose, varied kind of steel wire ropes are used in the manufacturing industry.

Transportation:  There are many kinds of wires used in the automotive as well aerospace industries. Within the aircraft or car, these wires need to withstand harsh environment such as heat, high altitude, pressure, and so on. Hence, these wires need to be corrosion resistant and capable of withstanding harsh environment. Depending on the project steel wires are chosen. Moreover, steel wires are also used activities such as transportation via trams, metros, etc.

Apart from the industries mentioned above, steel wires are extensively used in many other sectors such as oil and gas, entertainment, infrastructure, general engineering, etc.

Concluding thoughts: choosing the right wire

Steel wires are one of the important products for many industries. They are available in a variety of types of steel, sizes and so on. Therefore, you need to be careful in choosing the right steel wire for your project. In order to select the right steel wire, determine the needs of your project and understand the environment the wire will be functioning in.

You need to be careful while procuring desired steel wires. Ensure you are buying it high quality products from a trustworthy supplier. Tata nexarc is one such platform to procure high-quality steel. Log on to Tata nexarc, share your requirements, get quotes from verified vendors. Try now.